Optimizing Sealing Performance: What Engineers Should Know About Non-Metallic Gaskets in Modern Equipment Design
Non-metallic gaskets are becoming increasingly sought after as an engineered solution for numerous applications including as a load-sensitive sealing element in modern equipment.
Engineers spearheading the programs for non-metallic gasket manufacturing already know how pivotal reliable and consistent performance is – especially in modern equipment applications.
All-State Industries makes mention of key considerations engineers should abide by in non-metallic gaskets’ role in serving modern equipment design and just the importance of the part they play.
Necessary Selection Inputs
Material selection is one of the most important aspects in any manufacturing operation, and non-metallic gaskets are no exception. Before selecting a material, these six aspects should be considered, qualified, quantified, and ultimately settled.
Gaskets need to resist the process medium, cleaning chemicals, water vapor, oils, solvents, and other concentration changes, making overall fluid and containments are critical design input. If these issues are ignored there is potential for part failure through swelling, softening, embrittlement, chemical attack, and contamination.
The second design input to consider is temperature and thermal cycling. Items such as material properties, bolt load, flatness, and differential expansion are all impacted by temperature changes. By focusing on temperature and thermal cycling, defects such as relaxation, cracking, and thermal-ratcheting leakage can be properly addressed.
Similar to temperature and thermal cycling, pressure and pressure cycling warrant the same consideration. A high internal pressure can increase the separating load on the joint, which promotes extrusion. This could lead to a blowout or pressure-induced leakage.
In order to avoid local crushing or low-stress leakage points, flange geometry and stiffness need consideration during design.
Gaskets need to conform to the actual surface texture without being cut by it, which makes face finish and condition a critical input. If this goes ignored, there is potential of leakage caused by scratches, fretting, and overall gasket damage.
Lastly, service life and maintenance need to be weighed. Creep, stress relaxation, compression set, and aging establish retained sealing load.
Gasket Properties are a System
Non-metallic gaskets contain multiple properties, and when those properties are viewed as a working system rather than as individual aspects or characteristics of the part, a more comprehensive and optimized component is possible. When viewing properties through the lens as a whole system, it also helps in material selection.
When looking at the compressibility and recovery of a gasket, it’s an indication of how well the chosen material conforms under short-term load. Additionally, the rebound rate after unloading has occurred.
A loss of compressive load over time after the gasket is compressed is the creep relaxation rate. When relaxation rates are lower, retained bolt load and leakage risk improve.
The third property is arguably the biggest associated with gaskets of any kind and that’s seal-ability.
Factor in Assembly Operations
While it doesn’t happen often, it happens often enough to mention. Non-metallic gaskets might be well engineered and well manufactured, but they could still fail because of an uncontrolled installation into the modern equipment they were engineered and manufactured to serve.
Having a plan in place prior to installation can greatly reduce failed installs and placing a focus on the process, target load and torque method, lubricant condition, sequence, and inspection requirements, can lead to a smooth installation.
Some common practices to avoid a part failure as a result of an uncontrolled installation include inspecting flange faces for any concerns such as flatness, damage, corrosion, and any radial scratches.
It’s always best to keep your non-metallic gaskets clean, dry, and out of the flow path to avoid potential damage. When fasteners are ready to be tightened, do so in a cross-pattern sequence and in stages. Ensure torque tools are properly calibrated to ensure proper sealing of the gasket and that it’s not too tight or too loose.
Pivot to Non-Metallic Gaskets and Contact All-State Industries Today
All-State Industries has served as the turnkey rubber and plastic manufacturer that OEMs, supplier programs, and other customer bases have relied on for over 50 years. Our intentionality and focus on creating high-quality non-metallic components start with our pre-manufacturing engineering capabilities and non-metallic gaskets receive the same attention as any other part we produce.
With numerous production methods readily available, either our West Des Moines, Iowa, headquarters or one of our other facilities across North America, we have the team and expertise to ensure sealing performance in your non-metallic gaskets is optimized and your operations will run as expected.
Quality is a foundational pillar in everything that we do, and our quality management systems have been ISO 9001 certified for years and years to come.
Contact All-State Industries today for more information on our non-metallic gasket solutions and how we can transform your operations.